The Epson ME Office 960FWD resetter, also known as an adjustment program, is a specialized software tool designed to reset the waste ink pad counter in your printer. This utility essentially tricks your printer into believing that the waste ink pads have been replaced or cleaned, allowing normal operation to resume.
The resetter works by communicating directly with your printer’s internal memory system. It accesses the specific counters that track waste ink accumulation and resets them to zero. This process doesn’t physically clean the waste ink pads, but it removes the software restriction that prevents printing.
The adjustment program is particularly valuable because it addresses one of the most common reasons why otherwise functional printers become unusable. Rather than requiring expensive service center visits or premature printer replacement, this tool provides a cost-effective solution for extending your printer’s lifespan.
In this article, we will explain in more detail what a resetter is, how it works, how to use it, and where you can get it.
Table of Contents
- Common Error Messages
- What is Epson ME Office 960FWD Resetter?
- How the Resetter Tool Works
- How to Use Epson ME Office 960FWD Resetter
- Download Epson ME Office 960FWD Resetter Here
Common Error Messages
The Epson ME Office 960FWD displays several specific error messages when the waste ink pad counter reaches its limit. The most common message reads “Service Required” or “A printer’s ink pad at the end of its service life.” These messages indicate that the internal counter has reached its maximum value and requires intervention.
You might also encounter messages stating “Please contact Epson Support” or see red lights blinking in specific patterns. These visual and textual indicators all point to the same underlying issue: the waste ink pad counter has exceeded its programmed threshold.
The timing of these messages can vary significantly between users. Heavy printing, frequent cleaning cycles, or extended periods of inactivity can all influence when these errors appear. Recognizing the signs early allows you to prepare and obtain the necessary tools before your printer becomes completely inoperable.
What is Epson ME Office 960FWD Resetter?
The Epson ME Office 960FWD Resetter is a third-party software utility specifically designed for this printer model. Its primary function is to communicate with the printer’s internal memory and reset the waste ink counter back to zero. This counter is not a physical component but a software-based safeguard programmed by Epson. When the estimated saturation level of the maintenance pad (which absorbs waste ink during cleaning cycles and priming) reaches its limit, the printer locks down to prevent potential ink leakage. The resetter bypasses this lockout by clearing the accumulated count, allowing the printer to function again.
How the Resetter Tool Works
The Epson ME Office 960FWD resetter operates through a direct communication protocol with your printer’s internal memory system. When you run the adjustment program, it establishes a connection through your printer’s USB cable.
The software then accesses specific memory locations within your printer’s firmware where the waste ink counters are stored. These counters exist as numerical values that increment each time your printer performs cleaning cycles or encounters situations where excess ink needs absorption.
During the reset process, the program overwrites these counter values, returning them to zero or their factory default settings. This action effectively convinces your printer that new waste ink pads have been installed, removing the software restriction that prevents normal operation.
How to Use Epson ME Office 960FWD Resetter
1. Before you download and use the Epson ME Office 960FWD Resetter, first temporarily disable the antivirus on your computer. This is done to ensure that the reset process runs smoothly, as antivirus programs usually make mistakes in detecting resetter programs as dangerous. Additionally, make sure the printer is correctly connected to the computer using a printer USB cable.
2. You can download the Epson ME Office 960FWD Resetter via the link below this article.
3. After you download the resetter file, please extract the file by right-clicking and then selecting ‘Extract All’.
4. Open the extracted folder and run the file ‘AdjProg.exe’. Once the program opens, click ‘Accept’.
5. After the resetter program has been successfully run, please click the ‘Particular adjustment mode’ button.
6. Select ‘Waste ink pad counter’ in the Maintenance tab. Then click ‘OK.’
7. Tick the ‘Main pad counter’ & ‘FL Box Counter’ option, then click the ‘Check’ button, followed by clicking ‘Initialization’. After the reset is successful, click ‘Finish’. Then you can turn off the printer and turn it back on afterwards.
8. If the reset fails, try moving the printer’s USB cable to another available port on your computer, and then you can repeat the reset process.
Download Epson ME Office 960FWD Resetter Here
Remember, resetting doesn’t empty the waste ink pad. The pad will eventually become physically full and must be replaced to prevent leaks and damage. Monitor printer usage after resetting. Multiple resets without a pad replacement risk serious damage.
If you already understand what a resetter is, how it works, you will certainly be able to use the resetter in the best way and avoid the risks to your printer. If you need the Epson ME Office 960FWD Resetter, you can download it through the following link.
File Size: 976KB
File Type: .ZIP
OS Support: Windows 7/8/10/11 or higher
Maybe you would like other interesting articles?